LJTick-VRef
The LJTick-VRef is a Voltage reference accessory that outputs a stable 2.5V or 4.096V signal. More information…
CB37 Terminal Board
Provides convenient screw terminals for the DB37 connector on the LabJack U6, UE9, and T7. More information…
CB15 Terminal Board
Provides convenient screw terminals for the 12 digital I/O lines on the DB15 connector of compatible LabJack devices. More information…
Mux80 AIN Expansion Board
Analog input expansion board that adds 80 analog input channels. More information…
3ft DB37 M/F Serial Cable
A three foot DB37 cable, useful for connections between the Mux80 and CB37 Terminal Board(s). More information…
LM34CAZ Silicon Temperature Sensor
The LM34CAZ is ideal for cold-junction compensation(CJC) temperature measurements. More information…
EI1050 Digital Temperature- Humidity Probe
Uses two digital lines on any LabJack to retrieve temperature and relative humidity measurements. More information…
EI1034 Temperature Probe
Easy to use and very accurate temperature probe from Electronic Innovations Corp. More information…
EI1022 Temperature Probe
Easy to use and inexpensive temperature probe from Electronic Innovations Corp. More information…
LJTick-DAC
Provides a pair of 14-bit analog outputs with a range of +/- 10 volts. More information…
LJTick-Resistance
The LJTick-Resistance (LJTRx) makes it easy for LabJack devices to measure resistive sensors. More information…
LJTick-LVDigitalIO
A bidirectional logic shifting board for converting 3.3V logic down to 2.5V or 1.8V. More information…
LJTick-OutBuff
Increases the output current of the DAC outputs on LabJack devices. More information…
LJTick-InBuff
Very low bias current (1pA) input buffer which can directly measure pH sensors (electrode type sensors) and other weakly driven or high source impedance signals. More information…
LJTick-RelayDriver
Allows 2 digital I/O lines to each control a relay or other moderate load. More information…
LJTick-Proto
The LJTick-Proto (LJTP) consists of an 8×8 grid of holes for prototyping custom signal-conditioning ticks. More information…
LJTick-InAmp
Signal-conditioning module provides two instrumentation amplifiers ideal for low-level signals such as bridge circuits (e.g. strain gauges) and thermocouples. More information…
LJTick-Divider
The LJTick-Divider (LJTD) is a signal conditioning module designed to take two single-ended higher voltage analog signals, and divide them by a specified value. More information…
LJTick-CurrentShunt
The LJTick-CurrentShunt (LJTCS) is a signal-conditioning module designed to convert a 4-20 mA current loop input signal into a 0.47-2.36 volt signal compatible with the LabJack U3, U6, UE9, T7, or T4. More information…
RB16 Relay Board
Provides 16 industry standard relay module sockets to a LabJack U12. More information…
RB12 Relay Board
Provides 12 industry standard relay module sockets to a U3, U6, UE9, T4, or T7. More information…
PS12DC Power Switching Board
Controlled through 12 digital outputs, the PS12DC can switch power sources ranging from 5 to 28V DC. More information…
EI1040 Dual Instrumentation Amplifier
General purpose dual instrumentation amplifier. More information…
EB37 Experiment Board
Just like any breadboard, the EB37 is very useful for testing and validating electronic designs. More information…
CB25 Terminal Board
Provides screw terminal connections for the LabJack U12’s 16 extra digital I/O. More information…
5V 1.2A Barrel Jack PSU
This is the 5V, 1.2A, 2.1mm I.D. x 5.5mm O.D. x 9.5mm Barrel Jack PSU that ships standard with our UE9 and EB37 products. More information…
5V 2A USB PSU
This is the 5V 2A USB Power Supply that ships with the T7/T7-Pro. More information…